I had to do a find and replace a string on all of the wordpress post. This can only be done via a MySQL query and won’t take more than a minute.

This is how it’s done. In the following example, I will be finding X and replacing it with Y

The string will find X in every single post and replace it with Y. This also works with phrases, URLs etc..

update wp_posts set post_content = replace(post_content, 'X', 'Y')

Popularity: 1% [?]

There are many free TFTP server sortware out there, just install one.

First of all, make sure you have IP reachablity to the TFTP Server. You can do that via Ping…

Then check whether TCP port 69 is open. Usually it is not the case, but when it comes to troubleshooting, it is the first thing to check after a succesful Ping test.

Jump onto the router you are going to do the IOS upgrade.

Make sure the IOS you are going to replace it with is compatible with your router & also you have the necessary Flash / RAM.

If your Flash is big enough to have more than two IOS images, then you can straight away go and download it from the TFTP Server.

If you are going to have two IOS images in flash, you need to specify the router which image to load on boot. It can be done via the following command…

boot system flash IMAGE_NAME_HERE

Example:
Router(config)#boot system flash c2691-adventerprisek9_ivs-mz.124-15.T9.bin
If the flash is not big enough to have both images, you need to delete the old image.

I usually use the command show flash: then delete the content via the command delete flash:

You can see an example here…

Router#show flash: all
-#- --length-- -----date/time------ path
1 32293924 Mar 1 1993 00:23:52 +00:00 c2691-adventerprisek9-mz.124-5a.bin
31739904 bytes available (32296960 bytes used)
Router#delete flash:
Delete filename []? c2691-adventerprisek9-mz.124-5a.bin
Delete flash:c2691-adventerprisek9-mz.124-5a.bin? [confirm]
Router#
Router#
Router#
Router#show flash:
No files on device
64036864 bytes available (0 bytes used)

Now copy the IOS image from the TFTP Server

Copy tftp: flash:

Example here…

Router#copy tftp: flash:
Address or name of remote host []? 192.168.1.100
Source filename []? c2691-adventerprisek9_ivs-mz.124-15.T9.bin
Destination filename [c2691-adventerprisek9_ivs-mz.124-15.T9.bin]?
Accessing tftp://192.168.1.100/c2691-adventerprisek9_ivs-mz.124-15.T9.bin...
Loading c2691-adventerprisek9_ivs-mz.124-15.T9.bin from 192.168.1.100 (via FastEthernet0/1): !!!!!!!!!!

Sometimes the router might ask you to erase Flash: but I usually do that…

Reload the router and it should be able to run the new IOS Image.

If you happen to have more than one IOS on Flash: You can hardcode which version of IOS to load with the global config command.

Router(config)#boot system flash c2691-adventerprisek9_ivs-mz.124-15.T9.bin

Popularity: 1% [?]

If I ask that question to a number of people, I have a feeling I would get all sorts of answers. I think, Hard Disk Drive (HDD) reliability doesn’t necessarily depends on the manufacturer but it also depends on how it has been treated in a machine. In my opinion, a HDD in a machine with multiple power cuts would most likely have a short lifespan than one run with proper care.

Lets talk about the Manufacturer…

People have preference when it comes to HDD Manufacturer. When it comes to the manufacturer, I tend to go for Western Digital (WD) and solely because I had less bad experience with it compared to Maxtor…

I am not saying WD drives never fails, in fact I do have an old WD 80GB IDE drive here which died this morning; but it does have low percentage of failure.

Why does it die?

One person actually asked me this question and the answer is very simple. Any electronic equipment, or any functioning part will die at one point, its the same as human body, it all depends on how its been treated the background of it. When it comes to HDD, its the manufacturer.

How to stop a HDD from dying?

You can’t and you never know when it’s going to die, same as a human being… You never know when you are going to die. It all comes down to to proper care and how its been treated. For example, do not shut your machine down by pulling the plug, it WILL kill the HDD at one point! If you want to shut it down without doing it via the Operating System, press and hold the Power Button for 10 seconds and it should shut the machine down.

Conclusion

Treat a HDD like it is going to die the next minute and back it up on a regular basis. If you don’t have any important information on the disk, then it not a problem. You could either manually back it up on another drive, setup RAID on machine or even back it up to a remote server.

Popularity: 11% [?]

An interview with Russ White, CCIE No. 2635, a member of the Routing Protocol Design and Architecture Team at Cisco Systems. In this interview he presents valuable insights into CCDE Design Track Certification.

Popularity: 12% [?]